This tutorial shows the whole procedure to simulate a landslide of a hillslope from a initial condition of failure. The tutorial was done with the interFoam solver from openFoam on a non- Newtonian flow. The fluid has a variable kinematic viscosity (nu) based on the Bird-Carreau model. Failure scenario last only 6 seconds and results were recorded every 0.1 seconds. Final geometry and the landslide development were analyzed with paraView with predefined views (paraView states).

Computational fluid dynamics modeling with OpenFOAM could be challenging for water resources engineers since OpenFOAM models all types of fluids like water, air, heat and electromagnetism. On a normal hydrological software, it is implicit that the physical properties or the empiric formulation matches water on the liquid phase at temperatures around 20°C; however in a CDF program as OpenFOAM we have to define that the fluid we are working with is water and this increases the level of complexity on the model conceptualization and analysis.

But there is a interesting face of this complex fluid formulation in OpenFOAM: we can model any fluid, fluid type and turbulence condition; that means that we can model fluids like oil, alcohol, beer, or glycerine just with their property definition. In this tutorial we model and compare the behavior of 5 Newtonian fluids: beer, benzene, glycerine, olive oil and water. All fluids have been simulated on the same geometry and timeframe and all simulation output have been integrated in one paraView session for the comparative analysis of the fluid performance. Fluids were modeled with the interFOAM solver on turbulent conditions with the k-epsilon schema.

This tutorial is about a floating object stability simulation from a water surface oscillation (wave). The model was done with the interFoam solver that is a solver for two incompressible fluids, on isotermic conditions using a volume of control (VOF) phase-fraction interface approach. Turbulence was conceptualized on the model with the kEpsilon turbulence model. Simulation was done for 4 seconds with outputs every 0.05 seconds and runs in almost 5 minutes on OpenFOAM for Windows, better computation times are expected when run on Linux with paralleling computing.

A right assessment of the effluent mixing zone would require a baseline of sea currents, discharge flows, seawater and effluent density, bathymetry, waves, infraestructure geometry and a tool that can analyse the interaction of the mentioned factors. OpenFOAM is a numerical model for Computational Fluid Dynamics (CFD) modeling capable of modeling fluids with complex geometries, conditions and requirements; with OpenFOAM one can model compressible/uncompressible, single phase / multiphase, flows that mix, non-newtonian flows, etc. OpenFOAM comes with build-in tools for model construction and visualization, and there is Salome Platform for advanced mesh generation.

This tutorial show the entire procedure for the simulation of a effluent of 40 l/s into the ocean that has a current of 0.05 m/s. The model is on transient conditions, model simulation were done under uniform discharge rates, the development of the mixing zone was analyzed with paraView tools and a water chemistry component was introduced into the simulation with some Python scripts. 

Discretization is the “art” of transforming a continuous media as nature into discrete parts; for numerical models the spatial and temporal discretization have become a key issue in assuring model efficiency, output precision and the overall quality of the modeling work. Flow models are constructed to represent an specific requirement on the surface water/ groundwater flow regime (local scale), however, the model has to represent first the overall flow regimen (global scale). On the general model areas, an efficient spatial discretization criteria rules to keep the mesh elements as big as possible, meanwhile, in the areas of interest the model should be discretized into the smallest parts.

This tutorial will apply OpenFOAM to simulate the flow effect on submerged object using the simpleFoam solver and the k-epsilon turbulence schema. The tutorial develops the case of a submarine model against a flow current; the velocity and pressure applied on the submarine will be analyzed on the model results and flow paths will be plotted to see the main patterns around the submarine. Model output visualization is performed on Paraview that allows the representation of velocity and pressure vectors over the submarine.

This tutorial will demonstrate the modelling configuration to simulate a power dissipator in an open channel. The dissipator design is proposed on the Stormwater Drainage Manual from the Drainage Services Department of Hong Kong and  OpenFOAM will be used for the simulation with the interFoam solver since two immiscible and isothermal fluids are involved (water and air). The main variable of interest on the dissipator simulation is flow velocity to assess the efficiency of the dissipator.

There are many Global Circulation Models (GCMs) with historic and future data of Precipitation, Maximum Temperature and Minimum Temperature for different emission scenarios. Data is available on daily timescale from particular servers, in this tutorial we will show the main characteristics of the NASA NCCS THREDDS Data Server that provide the NASA Earth Exchange Global Daily Downscaled Projections (NEX-GDDP) dataset that has two of the four greenhouse gas emissions scenarios. Data from this dataset is available from 1950 to 2100 separated on historic and future with a spatial resolution of 0.25 degrees (~25km x 25 km). The tutorial show the main parts of the web server and scripts in Python to locate the closest model cell and to recursively download group of records.

Evaluation of hydrological processes as evapotranspiration, runoff, routing and infiltration require data as precipitation, flow, temperature and radiation on a daily basis. Required data for the hydrological modeling need to be accurate and must be completed over the period of study. Many times historical data from hydrological stations are incomplete and present many gaps that can be filled by the use of Artificial Intelligence tools as the Keras library in Python.

This tutorial show the procedure to run a complete script for the filling of missing precipitation in one station by the use of data from 2 nearby stations. The Python script is done on a Jupyter Notebook.

Drinking and residual water treatment, water intake into hydroelectric power stations or water treatment for industrial processes require the removal of suspended particles by sedimentation tanks. These hydraulic structures have a slow speed water inlet and a geometry that allows the decantation or precipitation of sediments along the settler path.

OpenFOAM is a open source software for Computational Fluid Dynamics (CFD) modeling with a series of solvers for different flow conditions. In this case we have used the driftFluxFoam solver to represent sediment precipitation in a sedimentator in a transient simulation of 6400 seconds. The tutorial contains 2 videos with the model description and its simulation.

Evaluation of crop yield can be tedious because sampling methods requires the actual counting of fruits for a whole tree or canopy area. If we want to optimize this time demanding task we can use new and open source machine learning algorithms available. We have selected Scikit-Learn for this tutorial, a machine learning library in Python for it ease to use, the available documentation and the sort of available tools. 

The tutorial covers the whole procedure of image representation, point of interest selection, template matching, cluster analysis and fruit counting. Python scripting was done in Jupyter Notebook, it is interactive and allows the user to add more points of interest or remove inaccurate points.

For OpenFOAM modelers the representation of topography can be painful due to the unstabilities and complexities of the Bezier Surfaces in Salome Platform. It is more stable to create the mesh by importing a full textured surface on a format file compatible with Salome. This tutorial show the process to create a STL file from a GeoTiff(.tif) file by scripts in Python. We have used the OSGeo4W Shell that comes with the normal QGIS instalation because it comes with the gdal library already installed.